FAQ

Location:Home > FAQ
Welcome to Kim Chemistry Q & A, where you can learn about Kim chemical consumption or questions of R & D industry, if you have any question, please contact us, we will answer your questions as soon as possible.

How to stick to instant adhesive ?

1.      Anchor hook principle:Fill the glue A over the two,the glue combines with water in the air and turn harden.

2.      Polymeric surface affinity: Cation anionic polymerization,some material has good affinity with water.

Is it the more viscosity,the faster the adhesive ?

No. More thick viscosity slower speed, because increased consistency must add a thickener, and then the speed will affect the tackifier.

Why albino?

Lively glue molecules, scattered around the place before the glue solidified , causing bleaching.

If instant glue points up, is the volume the same after hardening ?

As the case may be, the faster solidification, the less damage. Not more than 0.1% maximum loss.

Why the low whitening light scent?

The longer molecular chain, the molecule is not easy to shed lively, so more tasteless, less bleaching.

Why are there different consistency ?

Usually in response to the size of the gap material, and construction conditions depending on the customer.

Why use A carboxyl but not B carboxyl?

A carboxy is market mainstream products, the speed, strength and taste are good performance than B carboxyl .

May methyl stick stainless steel it ?

Yes. All the metal can use B carboxyl products. B carboxyl is good affinity for the metal than A carboxyl,

Is it the rougher on the surface the better stick ?

Generally yes. But there is a special surface treatment material exceptions or special column.

The PE is used in the bottle of glue,is it because of its bad affinity ?

Yes.PE is a high-density material, airtight.But AL is better than PE.

What is the relationship between the albino and glue ?

The faster ,the weaker albino.

What’s the reasons of why the speed of glue trun slowly ?

Environment, materials, operating practices,and the customer's own requirements Etc.

Why glue shelf life shorter?

Poor storage conditions , direct sunlight , long-term exposure to air , foreign body invasion.

What’s the reason of glue strength deterioration ?

1. Material change ,supplier change.

2 Material size, shape change.

3 Operating environment changes (such as seasonal changes).

4 Paste incomplete, poor adaptation.

The use of instant glue?

55 ~ 80.

What’s the best storage conditions of glue ?

Low temperature (10~15), dry, out of direct sunlight.

What’s the standard test environment ?

No uniform standards.Our R & D is a constant temperature 25 , humidity 70 to 80%.

The standard of S.G.S/ASTM/EN ?

At present, we have SGS / ASTM / EN proof, (ASTM F963-96a, European regulations for the EN-71).

Does the glue has a boiling point ?

Instant glue can not be measured boiling point at 1 atmospheric pressure , because it will be harden, it can be mearured at the atmospheric pressure 6mmHg under 65 .

The specific gravity in 20 ?

Generally speaking,the proportion of instant glue is almost the same as water.

What’s the flash point ?

When the glue turn flash point in the TDS, experiencing fire may burn, but does not spontaneous combustion.

What’s the dielectric ?

The higher the number, the better represent the conductivity.

What’s the oftening point ?

The temperaturer displayed on the TDS of instant glue,which makes the curing glue turn to iquid state and can’t stick. In the room temperature, the glue will be re-curing, but its adhesion will be reduced.

Does it has international common NO. ?

Any chemical res has its own NO.

How to remove instant glue ?

To remove the instant glue with acetone.

 

點擊這里給我發消息點擊這里給我發消息點擊這里給我發消息點擊這里給我發消息點擊這里給我發消息